Dapol Junction Bracket Signals

User avatar
Walkingthedog
Posts: 4972
Joined: Thu Oct 04, 2018 5:51 pm
Location: HAZLEMERE, BUCKS.
Contact:

Re: Dapol Junction Bracket Signals

#11

Post by Walkingthedog »

Or just cut the wire and splice in an extension with choc blocks or solder.
Nurse, the screens!
Hound Dog
Posts: 469
Joined: Thu Oct 04, 2018 7:46 pm
Location: Ayrshire
Contact:

Re: Dapol Junction Bracket Signals

#12

Post by Hound Dog »

I agree it looks like the JST micro connector and for sure there are jumper cables readily available for same, but equally it could also be any one of many other similar connector types from many other manufacturers eg TE/AMP or Molex etc...... are there any markings on the connector ?

Cutting the wires and adding a terminal block is the easiest solution but would certainly invalidate your warranty.
User avatar
teedoubleudee
Posts: 1116
Joined: Fri Oct 05, 2018 2:53 pm
Location: Downham Market
Contact:

Re: Dapol Junction Bracket Signals

#13

Post by teedoubleudee »

That looks like the type of plug and wire colours for an RC servo motor. If so you can buy extension cables, see below. No need to cut any wires or do any soldering.
https://www.ebay.co.uk/itm/10pcs-150mm- ... 0005.m1851

Longer lengths are available.
Most people are shocked when they find out how bad I am as an electrician
Gordon H
Posts: 6
Joined: Thu Oct 04, 2018 6:20 pm
Contact:

Re: Dapol Junction Bracket Signals

#14

Post by Gordon H »

teedoubleudee wrote: Thu Dec 05, 2019 12:12 pm That looks like the type of plug and wire colours for an RC servo motor. If so you can buy extension cables, see below. No need to cut any wires or do any soldering.
https://www.ebay.co.uk/itm/10pcs-150mm- ... 0005.m1851

Longer lengths are available.
It is certainly not one of those. That is a standard RC servo connector, this one is a miniature version.
As Hound Dog suggests, most likely a JST, but ought to be investigated further.
You might think that Dapol would list the connector part number in their associated documentation for just such a situation. Perhaps an email to them might produce an answer - but given their past record on apparent lack of technical knowledge about the electrical aspects of their own signal designs I wouldn't bet on it.
User avatar
Walkingthedog
Posts: 4972
Joined: Thu Oct 04, 2018 5:51 pm
Location: HAZLEMERE, BUCKS.
Contact:

Re: Dapol Junction Bracket Signals

#15

Post by Walkingthedog »

Dapol will be producing extension leads for the switches .
Nurse, the screens!
Rich123
Posts: 12
Joined: Thu Dec 20, 2018 11:04 am
Contact:

Re: Dapol Junction Bracket Signals

#16

Post by Rich123 »

Regarding the entry by Walking the Dog I have just read a review about Dapol Signals in the January 2020 edition of Hornby Magazine and it also advises that extension cables are to be produced. I think I'll wait for them to be released.

Many thanks to all contributors.
User avatar
Walkingthedog
Posts: 4972
Joined: Thu Oct 04, 2018 5:51 pm
Location: HAZLEMERE, BUCKS.
Contact:

Re: Dapol Junction Bracket Signals

#17

Post by Walkingthedog »

That’s where I read it.
Nurse, the screens!
User avatar
bulleidboy
Posts: 2310
Joined: Thu Oct 04, 2018 6:30 pm
Location: Basingstoke, Hants
Contact:

Re: Dapol Junction Bracket Signals

#18

Post by bulleidboy »

Just hope they bring out a SR version - I could do with a couple.
PeterBalcombe
Posts: 30
Joined: Thu Feb 14, 2019 6:30 pm
Contact:

Re: Dapol Junction Bracket Signals

#19

Post by PeterBalcombe »

Me too
Post Reply

Who is online

Users browsing this forum: No registered users and 2 guests