New Loco not working on programming track

User avatar
Walkingthedog
Posts: 4972
Joined: Thu Oct 04, 2018 5:51 pm
Location: HAZLEMERE, BUCKS.
Contact:

Re: New Loco not working on programming track

#21

Post by Walkingthedog »

Tim may I ask why you need insulated fishplates?
Nurse, the screens!
User avatar
Brian
Posts: 2215
Joined: Thu Oct 04, 2018 3:49 pm
Location: SE Kent
Contact:

Re: New Loco not working on programming track

#22

Post by Brian »

Using a siding or end of one for a Programming area. As shown in the NCE PowerCab manual page 12 link to manual
Image << Click the Icon to go to my website
User avatar
Walkingthedog
Posts: 4972
Joined: Thu Oct 04, 2018 5:51 pm
Location: HAZLEMERE, BUCKS.
Contact:

Re: New Loco not working on programming track

#23

Post by Walkingthedog »

Thanks Brian I always assumed it was safer to have a separate piece if track not attached to the layout.
Nurse, the screens!
User avatar
Steve M
Posts: 3461
Joined: Thu Oct 04, 2018 5:29 pm
Location: Rochester, Kent
Contact:

Re: New Loco not working on programming track

#24

Post by Steve M »

With insulated track joiners there is a chance that the rear wheels could bridge the gap. The danger then is that the whole layout could end up as the programme track with every loco on the same address.
Tricky this DCC stuff, init?
"Not very stable, but incredibly versatile." ;)
User avatar
Walkingthedog
Posts: 4972
Joined: Thu Oct 04, 2018 5:51 pm
Location: HAZLEMERE, BUCKS.
Contact:

Re: New Loco not working on programming track

#25

Post by Walkingthedog »

That was going to be my next point Steve. What if the loco moves slightly, which I understand they can, and shorts out the gap.
Nurse, the screens!
User avatar
Brian
Posts: 2215
Joined: Thu Oct 04, 2018 3:49 pm
Location: SE Kent
Contact:

Re: New Loco not working on programming track

#26

Post by Brian »

Walkingthedog wrote: Mon Jan 18, 2021 6:33 pm That was going to be my next point Steve. What if the loco moves slightly, which I understand they can, and shorts out the gap.
You ensure the section from IRJs to buffer stop used for programming is long enough to accommodate every loco/DMU etc plus at least 50mm. If that cant be achieved you should use a totally separate section of track for programming. Locos only move a few small amount when being programmed typically about 3 to 5mm
Image << Click the Icon to go to my website
User avatar
Walkingthedog
Posts: 4972
Joined: Thu Oct 04, 2018 5:51 pm
Location: HAZLEMERE, BUCKS.
Contact:

Re: New Loco not working on programming track

#27

Post by Walkingthedog »

You never know, one day I might find that out.
Nurse, the screens!
User avatar
Brian
Posts: 2215
Joined: Thu Oct 04, 2018 3:49 pm
Location: SE Kent
Contact:

Re: New Loco not working on programming track

#28

Post by Brian »

Doubt it ;)
Image << Click the Icon to go to my website
User avatar
Walkingthedog
Posts: 4972
Joined: Thu Oct 04, 2018 5:51 pm
Location: HAZLEMERE, BUCKS.
Contact:

Re: New Loco not working on programming track

#29

Post by Walkingthedog »

Thinking about it Brian. Only got 11 locos now.
Nurse, the screens!
Ron S
Posts: 115
Joined: Thu Oct 04, 2018 11:48 pm
Location: South Australia
Contact:

Re: New Loco not working on programming track

#30

Post by Ron S »

With NCE, outside of the programming track mode which reduces current, it allows you to read CV' s whereas programming on the main, you can't read CV's so you can change the address but set min & max speeds for matching locos, etc so you need a decent length of track to be able to determine the max speed you want.
With POM, one puts in the address you want to change & it only changes the locos that have that address so it is advisable not to have any loco with default address 3 on the layout at any one time, otherwise that will get changed too.
Last edited by Ron S on Sat Feb 06, 2021 9:59 pm, edited 1 time in total.
Ron

NCE DCC, 00 scale, very loosely based on GWR
Post Reply

Who is online

Users browsing this forum: No registered users and 0 guests