Hi Rog - Not sure of the size (ohms) - it's pink! If I were to double-up, would the additional resistor be in-line with the one already in place (on the red wire) - or could I place the additional one on the black wire? Barry
Wykeham - Somewhere in the south!
- bulleidboy
- Posts: 2313
- Joined: Thu Oct 04, 2018 6:30 pm
- Location: Basingstoke, Hants
- Contact:
Re: Wykeham - Somewhere in the south!
Re: Wykeham - Somewhere in the south!
If you have already a series resistor, then add the second one in series. i.e. In the supply line or return wire. (Doesn't matter which).
If you used a self adhesive LED strip of LEDs which are usually in groups of three with a built in resistor per three LEDs, then the additional series resistor added needs to be probably around 10K (10,000 Ohm) .
A bit of trial and error in Ohm size is needed to get the light level down.
You can use a 20K liner variable trim Pot with a LED strip and set the illumination level with the adjustment, then remove pot, measure Ohm value and choose a fixed resistor to the nearest value read. Note, on a standard LED it is essential that a 1K resistor is also in circuit when using a adjustable Pot. Failure to do so will result in the LED blowing when the pot is set to minimum, as this is No (zero) resistance!
If you used a self adhesive LED strip of LEDs which are usually in groups of three with a built in resistor per three LEDs, then the additional series resistor added needs to be probably around 10K (10,000 Ohm) .
A bit of trial and error in Ohm size is needed to get the light level down.
You can use a 20K liner variable trim Pot with a LED strip and set the illumination level with the adjustment, then remove pot, measure Ohm value and choose a fixed resistor to the nearest value read. Note, on a standard LED it is essential that a 1K resistor is also in circuit when using a adjustable Pot. Failure to do so will result in the LED blowing when the pot is set to minimum, as this is No (zero) resistance!
- bulleidboy
- Posts: 2313
- Joined: Thu Oct 04, 2018 6:30 pm
- Location: Basingstoke, Hants
- Contact:
Re: Wykeham - Somewhere in the south!
Might have to do some "Googling" for that one BrianWalkingthedog wrote: ↑Tue Apr 13, 2021 7:09 pm What ever you put inside to stop the light bleed will need to be painted the same colour as the 12 inch to the foot version.
- bulleidboy
- Posts: 2313
- Joined: Thu Oct 04, 2018 6:30 pm
- Location: Basingstoke, Hants
- Contact:
Re: Wykeham - Somewhere in the south!
Following on from Brian's (WTD) suggestion, I have painted the inside of the carriage - I think it did the trick. I also, as Rog (RJ) suggested, added another resisitor. I think it has worked?
IMG_0935 by Barry Clayton, on Flickr
IMG_0935 by Barry Clayton, on Flickr
- Walkingthedog
- Posts: 4977
- Joined: Thu Oct 04, 2018 5:51 pm
- Location: HAZLEMERE, BUCKS.
- Contact:
Re: Wykeham - Somewhere in the south!
It has that perfect light yet gloomy look.
Nurse, the screens!
Re: Wykeham - Somewhere in the south!
Nailed it again Barry, even though the picture is to show the results of your tinkering to get the lighting right the reflection off the carriage lights on the rails make the scene so lifelike. You certainly have a talent for setting a scene.
Puddles
Puddles
It does not take me long to do five minutes work.
Nostalgia is not what it used to be.
Nostalgia is not what it used to be.
-
- Posts: 908
- Joined: Thu Oct 04, 2018 7:42 pm
- Contact:
- teedoubleudee
- Posts: 1116
- Joined: Fri Oct 05, 2018 2:53 pm
- Location: Downham Market
- Contact:
Re: Wykeham - Somewhere in the south!
Looking good BB
Most people are shocked when they find out how bad I am as an electrician
Who is online
Users browsing this forum: Google [Bot] and 0 guests