black 5 loco/ tender connection
- Walkingthedog
- Posts: 4960
- Joined: Thu Oct 04, 2018 5:51 pm
- Location: HAZLEMERE, BUCKS.
- Contact:
Re: black 5 loco/ tender connection
You don’t need a different tender John if you use the plug and socket, just needs a bit of rewiring.
Nurse, the screens!
-
- Posts: 758
- Joined: Fri Oct 19, 2018 8:32 am
- Location: Norham, Northumberland
- Contact:
Re: black 5 loco/ tender connection
Brian if you look at the service sheet for this R number Brian... the loco used the old chassis and ring field motor block (empty block) using the block to use pickups ect ...The old chassis does not have a convenient place to mount the plug socket. I would not do it with the old ring field chassis anyway.
If only there was enough hours in the day..................John
- Walkingthedog
- Posts: 4960
- Joined: Thu Oct 04, 2018 5:51 pm
- Location: HAZLEMERE, BUCKS.
- Contact:
Re: black 5 loco/ tender connection
Must be space for those tiny Hornby sockets, they’re only 1/4 inch wide or less.
Nurse, the screens!
-
- Posts: 758
- Joined: Fri Oct 19, 2018 8:32 am
- Location: Norham, Northumberland
- Contact:
Re: black 5 loco/ tender connection
You have look at the old style ring field chassis under side Brian. It is very low down on the track. If you cut hole out to fit plug there is not much left to hold bottom of chassis together. I think it would weaken it on the underside. If you are going to do that you may as well just run couple of extention wire into the tender and solder to the pick up and front pin wire. That was you dont have to cut up the chassis bottom.
If only there was enough hours in the day..................John
- Walkingthedog
- Posts: 4960
- Joined: Thu Oct 04, 2018 5:51 pm
- Location: HAZLEMERE, BUCKS.
- Contact:
Re: black 5 loco/ tender connection
I agree it would be betterr without the plug. Maybe the socket could be in the loco??
Nurse, the screens!
-
- Posts: 758
- Joined: Fri Oct 19, 2018 8:32 am
- Location: Norham, Northumberland
- Contact:
Re: black 5 loco/ tender connection
I dont know what it wants a socket for, all it needs is good service.
If only there was enough hours in the day..................John
- Walkingthedog
- Posts: 4960
- Joined: Thu Oct 04, 2018 5:51 pm
- Location: HAZLEMERE, BUCKS.
- Contact:
Re: black 5 loco/ tender connection
Neither do I but as you brought it up I thought I’d discuss it. A bit of adjustment and a clean will do the trick.
Nurse, the screens!
-
- Posts: 758
- Joined: Fri Oct 19, 2018 8:32 am
- Location: Norham, Northumberland
- Contact:
Re: black 5 loco/ tender connection
No I didnt,,,,, clubman did post 8....john
If only there was enough hours in the day..................John
- Walkingthedog
- Posts: 4960
- Joined: Thu Oct 04, 2018 5:51 pm
- Location: HAZLEMERE, BUCKS.
- Contact:
-
- Posts: 758
- Joined: Fri Oct 19, 2018 8:32 am
- Location: Norham, Northumberland
- Contact:
Re: black 5 loco/ tender connection
Did I,,,,,,,, wish I hadn't,,,,,,,, I gave bad advice then. Must admit I had not looked at the chassis at that point and noticed it had the old ring field chassis. Any way that is my defence your honour................
If only there was enough hours in the day..................John
Who is online
Users browsing this forum: Google [Bot] and 0 guests