Just A Thought.
Posted: Wed Feb 09, 2022 12:09 pm
Now this morning I saw the proposed retail price of some lovely new coaches and they do look nice! But at a proposed £60 each (Or are they each? Is £60 for the rake of three. It is unclear) are they a little too dear for most peoples pockets? Yes, with inflation as it stands that £60 will most likely seem cheap in the not too distant future and they are lovely looking models, but what is the limit to how much the prices in our hobby go up before the hobby collapses as models can no longer be made to the standards desired due to costs of producing them will meet the maximum price that the average modeller can afford to pay?
Are we now reaching a point where less and less modellers are buying and therefore prices are going up and up because production runs are far less than in the past?
The past limited editions were limited to runs of 5000 and then 1000... But these seem today like ordinary production run figures?
The tight squeeze in this hobby comes from another direction in the form of 3D printing, and ok, at the moment as good as 3D printers are (And they can make some lovely models in themselves!) they are not quite there compared to todays ready to run finescale models, but they are certainly up to yesterdays models in what we now deem to be in the lovable Railroad range by Hornby (And I am not knocking that range as if it wasn't for that range, some of us would not know where to turn to buy new models).
But the competition from the 3D side is certainly something to take note.
I have recently ordered two 3D model loco bodies in 7mm scale narrow gauge at a cost of £20 each which will take a little while before they will get to me so I eagerly await. These will be my first 3D examples to come my way so it is rather exciting. The bodies are designed to fit on those little Hornby Railroad 0-4-0's so I really can't go wrong! Cheap and cheerful modelling!
But is this where our hobby is taking us in the future and I don't neccessarily mean 3D?
We do not know, but if prices continue to rise faster than peoples income, then we may well see some dramatic changes in the future. This hobby could be set to change! The question is will the manufacturers out there be ready for change if or when it comes? I can understand what I say can be frightening to the manufacturers, especially the smaller ones, but planning ahead now may put them in a position that if it does come they can survive.
And this is what I want to see. Both the modeller being able to buy what they want, and the manufacturers earning themselves the money they need to survive, and the small kit builders happily churning out their kits as well so we are all happy.
The problem we have at the moment is where a potential newcomer looking at the hobby may see the higher prices of the beautiful models and not be aware that there are budget ways to start off in the hobby and one does not have to spend a lot unless one wants to as it is a shame when some see the prices and decide it is not for them.
Are we now reaching a point where less and less modellers are buying and therefore prices are going up and up because production runs are far less than in the past?
The past limited editions were limited to runs of 5000 and then 1000... But these seem today like ordinary production run figures?
The tight squeeze in this hobby comes from another direction in the form of 3D printing, and ok, at the moment as good as 3D printers are (And they can make some lovely models in themselves!) they are not quite there compared to todays ready to run finescale models, but they are certainly up to yesterdays models in what we now deem to be in the lovable Railroad range by Hornby (And I am not knocking that range as if it wasn't for that range, some of us would not know where to turn to buy new models).
But the competition from the 3D side is certainly something to take note.
I have recently ordered two 3D model loco bodies in 7mm scale narrow gauge at a cost of £20 each which will take a little while before they will get to me so I eagerly await. These will be my first 3D examples to come my way so it is rather exciting. The bodies are designed to fit on those little Hornby Railroad 0-4-0's so I really can't go wrong! Cheap and cheerful modelling!
But is this where our hobby is taking us in the future and I don't neccessarily mean 3D?
We do not know, but if prices continue to rise faster than peoples income, then we may well see some dramatic changes in the future. This hobby could be set to change! The question is will the manufacturers out there be ready for change if or when it comes? I can understand what I say can be frightening to the manufacturers, especially the smaller ones, but planning ahead now may put them in a position that if it does come they can survive.
And this is what I want to see. Both the modeller being able to buy what they want, and the manufacturers earning themselves the money they need to survive, and the small kit builders happily churning out their kits as well so we are all happy.
The problem we have at the moment is where a potential newcomer looking at the hobby may see the higher prices of the beautiful models and not be aware that there are budget ways to start off in the hobby and one does not have to spend a lot unless one wants to as it is a shame when some see the prices and decide it is not for them.