New layout design - What do you think?

Help with designing your track work
Post Reply
PlumbersMate
Posts: 9
Joined: Wed Nov 03, 2021 7:15 pm
Contact:

New layout design - What do you think?

#1

Post by PlumbersMate »

Hi everyone,

This is my proposed layout design. It is 3.6 x 3.1 meters. I have plans to have two cutouts and can walk around the layout edges, so will be able to reach all areas.

I wanted a tail-chaser design but purple\yellow track will be hidden behind a scenic 'break'. So the tail-chaser effect will not be so obvious.

It uses Peco Streamline points with all other track flex. The minimum radius is 2nd.

Behind the scenic break there is a access to a lower fiddle yard. One track goes down on the left and one on the right.

Any constructive comments would help.

Thank you in advance.

Image
User avatar
cadman
Posts: 115
Joined: Thu Oct 04, 2018 6:37 pm
Location: Leighton Buzzard
Contact:

Re: New layout design - What do you think?

#2

Post by cadman »

The Reverse Loop will need some attention, will need a R.L.M if a DCC layout.
Sorry I'm late but I couldn't get my flip-flops to work :roll:
User avatar
RogerB
Posts: 1380
Joined: Thu Oct 04, 2018 9:17 pm
Location: Dorset
Contact:

Re: New layout design - What do you think?

#3

Post by RogerB »

The outer yellow track does not connect on the r/h side, nor the inner track on the l/h side. R-
Young at heart. Slightly older in other parts.
User avatar
RAF96
Posts: 525
Joined: Fri Oct 05, 2018 6:33 am
Location: Dereham, Norfolk, UK
Contact:

Re: New layout design - What do you think?

#4

Post by RAF96 »

Some of the orange sidings are too short for anything but a single small loco.
brian1951
Posts: 1267
Joined: Thu Oct 04, 2018 5:52 pm
Contact:

Re: New layout design - What do you think?

#5

Post by brian1951 »

RogerB wrote: Thu Nov 04, 2021 5:26 am The outer yellow track does not connect on the r/h side, nor the inner track on the l/h side. R-
They connect to the lower fiddle yard, as stated by the OP.
User avatar
RogerB
Posts: 1380
Joined: Thu Oct 04, 2018 9:17 pm
Location: Dorset
Contact:

Re: New layout design - What do you think?

#6

Post by RogerB »

Thanks Brian, missed that. R-
Young at heart. Slightly older in other parts.
PlumbersMate
Posts: 9
Joined: Wed Nov 03, 2021 7:15 pm
Contact:

Re: New layout design - What do you think?

#7

Post by PlumbersMate »

cadman wrote: Wed Nov 03, 2021 9:50 pm The Reverse Loop will need some attention, will need a R.L.M if a DCC layout.
I had not noticed the Reverse Loop. It took me a while to see it.

I little advise will help. I have attached another picture. There are two green circles. Can I isolate this track length and wire the RLM here?

Image
User avatar
Brian
Posts: 2195
Joined: Thu Oct 04, 2018 3:49 pm
Location: SE Kent
Contact:

Re: New layout design - What do you think?

#8

Post by Brian »

Assume your layout will be DCC (Digital) operated. If so then the answer is .... The rule of a Reverse loop is that the longest complete train - Loco and all carriages or wagons must fit inside the loops isolated track section. i.e. in between the entrance and exit IRJs

I have marked the plan with what I consider to be the longest RLM section shown by the Blue line. You would use six IRJs and feed the blue outlined area from the RLM output.
RLM area.jpg
Image << Click the Icon to go to my website
PlumbersMate
Posts: 9
Joined: Wed Nov 03, 2021 7:15 pm
Contact:

Re: New layout design - What do you think?

#9

Post by PlumbersMate »

Dear Brian, Thank you for the info. That makes sense. I'll bear it in mind when I come to build.
User avatar
Chops
Posts: 1098
Joined: Sat Oct 06, 2018 8:11 am
Location: El Paso, Texas USA
Contact:

Re: New layout design - What do you think?

#10

Post by Chops »

Good eye, I could not see that for love or money. This is why I stick to circles.
Post Reply

Who is online

Users browsing this forum: No registered users and 0 guests